Network Cable Tester Detector LCD Digital Electrical Ethernet Cable Wire Tracer Line Finder with Multimeter Tool Kit

Feature: 1. Multifunctional: This network cable tester includes poe tester, anti interference network cable scan, conduction tester, voltage test, fault distance locator, port flashing, vibration mode, volume adjustment, multimeter, line length test and LED torch function. 2. 3 Mode Switching: This network cable tester has a unique anti interference digital scan mode, analogue mode, Poe mode. 3000m maximum cable finding distance. 16‑20VP P super strong signal to the cable tracer. You can set the frequency and the three modes can be switched freely. Equipped with a professional analogue tone generator, which makes a louder sound when it is close to the target cable. The sensitivity of the sensor can be adjusted using the scroll wheel on the cable tracer receiver to narrow the tracking range. A silent vibration mode can also be used to avoid disturbance. 3. Multiple Measurements: The multifunction multimeter can measure or test temperature, continuity, voltage, current, resistance, diodes, NCV and more. All accessories required for measurements are included in the package. Network cable tester, multimeter with DC AC voltmeter and ohms voltammetry in one, circuit tester to measure voltage, current. k type probe to measure temperature 20‑1000°C, AC voltage, current test range 4‑400V, 1.0A‑10A. NCV power display and diode test. 4. Hub Blink: The network cable tester identifies the pins providing power and detects the voltage, locating the network port by the blinking port lights on hubs and switches (blinking every 1 second). Suitable for use with 600M hubs switches. Measurement range includes circuit tracing, short circuit testing, breakpoint identification, etc. 5. Fully Equipped: The cable length measurement can be done with 2 core metal cable, CAT5 CAT6 network cable, telephone cable, coaxial video cable. The cable tester includes transmitter, receiver, crocodile clip cable, temperature K type test cable, RJ45 cable, USB cable, 9V battery. 6. Long Continuous Operating Time: The cable tester is equipped with a 1250 mA rechargeable lithium battery, which can operate continuously for 8 hours or standby for several months on a 3 hour charge from a 5V 2A charger. The receiver uses a 9V battery for up to 2 hours of continuous operation. Specification: Item Type: Network Cable Tester Material: ABS Analogue Line Finding Function: Yes Short Circuit Pass Through: Multimeter measurement Powered POE Switch: Yes Pair Function: Yes Switch Light Port Flashing: Yes Noiseless Digital Line Hunt: Digital vibration Line Voltage: Multimeter measurement POE Voltage Measurement: Yes Operation Wiring Indication: Yes Other Features: Multimeter pen prompt function, length self calibration function, LCD display, white torch function, adjustable volume for analog line finding, adjustable sensitivity for digital line finding, low voltage detection, white backlight, Adjustable sensitivity for digital tracing, low voltage detection, white backlight Other Features: Energy saving design, line finding distance of 3KM, switchable analogue line finding frequency Red Light Pen Function: Yes Multimeter Function: Yes DC Voltage: 400mV-1000V±(0.8%+3) AC Voltage: 4V-400V±(1 .5%+5) DC Current: 1.0A-10.0A±(1.2%+4) AC Current: 1.0A-10.0A±(2.0%+5) Resistance: 200Ω-20MΩ±(2%+6) On Off Beep: < 50 Ω buzzer beeps Diode: Yes Temperature (Type K):-20-1000°C±(2.0%+15) Network Cable Length Measurement: Approx. 600m / 1968.5ft Coaxial Cable Length Measurement: Yes Network Cable Short Circuit Broken Circuit: Yes Battery: Main Unit: 1 x 1250mAh rechargeable lithium battery (included), Wire Finder: 1 x 6F22 9V 800mAh dry cell battery (included) How to Use: Open the package and remove the product ready for use Package List: 1 xNetwork Cable Tester 1 x Host Lanyard 1 x USB Cable 1 x Instruction Manual 1 x Cable Finder 1 x Battery 2 x Test Pen 1 x Temperature K Type Test Cable 1 x RJ45 Cable 1 x Crocodile Clip Cable 1 x Storage Bag